I've been wanting to change my interior for awhile now.

So here is what I ordered:
Charcoal carbon fiber leather fabric (its like a dark gray color)


Alpine Type-S SPS-17C2 speakers (2 sets)


Xtreme Dynamat

2 cans of 3M spray on glue
(not pictured)
I also ordered about 20 blue LEDS which will go in all the vents, under the front seats, behind the seatbelt pillars (front and rear), in the rear cupholders/cubbys, in the front panel cubbys, and in the glovebox which will all be connected to an on/off switch.




I'm using charcoal CF leather cause it will match my Redline shifter and ebrake boot along with my armrest which is black CF leather and charcoal CF leather.


Here is some speaker work:
BEFORE:


AFTER:



I also did some work on the seatbelt pillars:




The before and after:



The rear passanger panel has leather (which was a pain in the butt) but I still have to put the 3 pieces back together.








Some finished items...

Passanger door


rear passanger panel


finished pillars w/ NBM paint (thanks to widetc )


The next pics are of the placement of the leds....

rear panels with 2 leds (1 in the cubby & 1 in the cupholder)


Passanger door (2 leds in the door cubby)


seatbelt pillar (1 led per pillar)


I took some quick pics of my trashed/dirty car.






Some more work...




My poor car...







The following are pics of work done with a dirty car. I was in a hurry to post pics so please leave the dirty car beating to a low please. I'm not a cameraman like Gardiner so forgive that too. Also if you look close in some pics you can see the new speakers installed

My completed interior (except for the front pillars)
Drivers door:





Driver side(front/back):



LOOK CLOSE... I see blue LEDS in the cupholder.




Passanger side(front/back)(...nice lookin' speakers):




Now for the long awaited LEDS. These were taken in my garage with the garage door shut and all the lights off... and my camera SUCKS cause I trashed a lot of pics.

Rear passanger panel:



Drivers seatbelt pillar:


Center waterfall vents:


Passanger vents:


Rear diamond plate floor mat with under seat lights:



Here are some pics with all my leds turned on...






Now for the daytime pics in the garage with the garage door open...
My glovebox(dirty!):


Passanger door:


Driver seatbelt pillar(I likes):


Drivers vents:


Rear drivers panel:


Well thats it for the pics. I have some leftover leather so I'll be doing the front pillars when I figure out how to remove them. I'm sure I'll still have extra so I'll see what else I can do.

LMK what you think!!

-----

great job.....looks great

-----

Great job... it looks great. Where did you get your supplies from?

-----
PTC

DAMN! You did some real quality work!!!! I am quite impressed! Very nice!

-----

Wow, When I saw the roll i was skeptical, but it turned out amazing. Good work!!!

-----

Thanks everyone. Its was some hard work, but I love the outcome. Funny thing is I had never done anything like this before and now I'm telling people how to do it.

-----

hey not bad with the work, where did u get the supplies, cause i want to do something similar to my car. where is everything connected to? Like do u have a on off switch connected?

-----
&D

AWSoME JoB...i SOOOO LoVE THE LOOK OF iT ALL...CAN YA COME TO HAWAii & MAKE MY CAR ALL PRETTY TOO? LOL WHERE DiD YOU GET THE MATERiAL FROM?

-----
VEE SE HAWAii BiG iSLE CHAPTER

clean interior, i have a question on how u got the leds to the top circular vents though? once again nice interior

-----
&D